Advanced build
Golden retriever, large grid Perler bead pattern
A 58-wide golden retriever. At this size individual fur strokes start to separate — the payoff for the extra beads.
- Grid
- 58 × 58
- Colors
- 13
- Beads needed
- 3,364
- Boards
- 4 boards, 58×58
- Build time
- 11½–13½ hours
- Color card
- Perler
The full chart is above, at actual size. Printing it, or exporting it as a PDF with a shopping list, is a separate step in the Studio — you do not need either to build from this page.
Colors and bead counts
Sorted by how many of each you will need, so the biggest pile goes down first. Codes are Perler codes.
| Color swatch | Code | Color | Beads |
|---|---|---|---|
| P01 | White | 2,225 | |
| P21 | Light Brown | 350 | |
| P98 | Sand | 284 | |
| P85 | Gold | 148 | |
| P35 | Tan | 111 | |
| P02 | Cream | 78 | |
| P18 | Black | 47 | |
| P20 | Rust | 43 | |
| P12 | Brown | 35 | |
| P17 | Grey | 26 | |
| P33 | Peach | 11 | |
| P244 | Rose | 5 | |
| P63 | Blush | 1 | |
| Total | 3,364 | ||
Buy a little extra White — at 2,225 beads it is the deepest pile on this chart, and it is the shade you run out of first if you sort a few early. A handful of spares covers the bead that slips under the pegboard.
Building it
This is an advanced build by the usual bead-count thresholds — more than 600 beads and more than ten colors. Budget an afternoon, sort every color before you start, and do not leave it half-placed overnight.
- Sort before you place. Make a pile per color using the table above. Ten colors or more, so label each sorted tray with its code from the table above before you start — the difference between a 11½ to 13½ hours build and a much longer one is usually the re-sorting.
- Work from the top-left corner. The grid orientation is fixed, so there is no mirroring to figure out. Row by row beats jumping around.
- Iron with parchment. Not wax paper — wax melts and bonds to the beads. Perler beads fuse clean on medium heat around 150 to 170°C, steam off, slow circles, and lift the paper after 10 seconds to check. You want the holes starting to close but still visible.
- Flip and repeat. Both sides means a sturdier piece, which is what a framed wall piece wants.
- Mount it while it cools flat. If it is going on the wall, the back gets a short strip of double-sided tape or a small D-ring at each board corner once it is fully cool.
How this chart was color-matched
The photo was matched to real Perler beads using the CIEDE2000 formula in CIELAB space, then dithered with Floyd–Steinberg so gradients break into a bead pattern instead of banding. Plain RGB distance fails badly on skin tones and pale shadows, which is where most photo converters give you a flat beige face. Everything here was produced by the Beadful Studio converter — the same tool you can point at your own photo.
How the four boards come together
13 colors across four boards is where the pile of sorted tray rows really pays off: group the colors into two trays by quadrant, so the 13 shades never have to cross the whole workbench in one sweep. The seam between boards is the one place a large piece fails, so before you iron, press each board's edge against the next until the pegs click, then run your thumb along the join. Perler beads sit a touch loose in the pegs, so press each quadrant down with a fingertip as you place.
Questions about this pattern
How many beads do I need for the golden retriever, large grid pattern?
3,364 beads in 13 colors. That fills the 58 by 58 grid almost completely, because the background is converted along with the subject. A standard 29 by 29 pegboard holds 841 beads and a 58 by 58 four-board layout holds 3,364.
Do I need a specific bead brand?
No. This chart was generated on the Perler color card, but every 5mm fuse bead brand — Perler, Hama, Artkal, MARD, Nabbi — fits the same grid, and the square boards interlock across brands. Match by color rather than by code, because Perler P01 and Hama H01 are both white but not the same white.
Which pegboard do I need?
Four 29×29 boards interlocked in a 2×2 layout, giving a 58 by 58 grid. Any standard 5mm square board works, including mixed brands.
How long does it take to make?
Roughly 11½ to 13½ hours of placement at 250 to 300 beads an hour, plus ironing. The larger versions are several hours of work. If this is your first build, do one board in a single session and leave the multi-board pieces for later.
What ironing settings should I use?
Parchment paper rather than wax paper, a dry iron on medium heat around 150 to 170°C, steam off, moved in slow circles. Check after about 10 seconds: the holes should begin to close but still be visible. Fusing both sides gives a sturdier result. Cool it flat under books for five minutes.
Can I change the size?
Yes, and you will need to if your board does not match. Load the photo in the Studio and set the grid width to 29 or 58 — the converter will rebuild the pattern against that grid and recalculate the color list.
Are these patterns free to use?
Yes. Viewing the chart and building from it is free. You do not need an account to look at any pattern on this page.
Other patterns
Corgi portrait
Golden retriever portrait
Shiba portrait
Corgi portrait, large grid
Shiba portrait, large grid
Corgi portrait in Hama colors
Still deciding what to buy?
The bead size guide covers 5mm versus 2.6mm, the color guide explains what 72 and 168 colors really give you, and the board size guide lists every pegboard layout with its bead count and build time.